Ошибка 057-03 P0341

Электрика для honda cr-v вопросы ответы и информация

Re: Ошибка 057-03 P0341

Сообщение SOS » Ср апр 04, 2012 10:12 am

Ошибка 057-03 P0341



P0341 Неправильный показатель / не отрегулирован датчик положения распредвала



вот это выдает программа диагностики.



Возможные причины и места неисправностей:

- Датчик положения распределительного вала впускных клапанов

- Датчик положения коленчатого вала

- Цепь привода ГРМ

- Фазы газораспределения

- Муфта системы VTC

- Клапан системы VTC

- Проводка и разъемы

- Блок управления двигателем



методы устранения ошибки 057-03 в зависимости от ошибки P



DTC Troubleshooting: P0344 (57)

DTC P0344: CMP Sensor A Intermittent Interruption





1. Note the following freeze data.



Engine speed

Vehicle speed



2. Do the DTC CLEAR in the CLEAR MENU with the Honda PGM Tester or the HDS.



3. Start engine, and let it idle for 10 seconds.



4. Check the CMP NOISE 1 COUNT in the DATA LIST with the Honda PGM Tester or the HDS.



Is 0 count indicated?



YES - Go to 5.

NO - Go to 8.



5. Test-drive the vehicle for several minutes in the range of the recorded freeze data.



6. Check the CMP NOISE 1 COUNT in the DATA LIST with the Honda PGM Tester or the HDS.



Is 0 count indicated?

YES - Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at CMP Sensor A and the ECM/PCM.n



NO - Go to 7.



7. Check for poor or loose connections and terminals at these locations:



CMP sensor A

ECM/PCM

Engine ground

Body ground



Are the connections and terminals OK?

YES - Go to 8.

NO - Reconnect the connectors or terminals,then go to 11.



8. Check for damage on the CMP sensor A pulse plate.



Is the plate damaged?

YES - Replace the CMP sensor A pulse plate, then go to 11.

NO - Go to 9.



9. Turn the ignition switch OFF.



10. Replace CMP sensor A.



11. Turn the ignition switch ON (II).



12. Do the ECM/PCM RESET in the CLEAR MENU with the Honda PGM Tester or the HDS.



13. Do the ECM/PCM idle learn procedure.



14. Start the engine, and let it idle for 10 seconds.



15. Check for Temporary DTCs or DTCs in the DTCs MENU with the Honda PGM Tester or the HDS.



Are any Temporary DTCs or DTCs indicated?

YES - If DTC P0344 is indicated, check for poor connections or loose terminals at CMP Sensor A and the ECM/PCM, then go to 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC troubleshooting.

NO - Troubleshooting is complete.n



DTC Troubleshooting: P0341 (57)

DTC P0341: CMP Sensor and CKP Sensor Incorrect Phase Detected



1. Turn the ignition switch ON (II).



2. Do the DTC CLEAR in the CLEAR MENU with the Honda PGM Tester or the HDS.



3. Start the engine.



4. Check for Temporary DTCs or DTCs in the DTCs MENU with the Honda PGM Tester or the HDS.



Is DTC P0341 indicated?

YES - Go to 9.

NO - Go to 5.



5. Do the VTC TEST in the INSPECTION MENU with the Honda PGM Tester or the HDS.



Is the result OK?

YES - Go to 6.

NO - Go to 9.



6. Test-drive at a steady speed between 30-60 km/h (19-38 mph) for 10 minutes.



7. Check the VTC STATUS in the DATA LIST with the Honda PGM Tester or the HDS.



Is it ON?

YES - Go to 8.

NO - Go to 6 and recheck.



8. Monitor the OBD STATUS for DTC P0341 in the DTCs MENU with the Honda PGM Tester or the HDS.



Is it FAILED?

YES - Go to 9.

NO - If it is PASSED, intermittent failure, system is OK at this time. If it is NOT COMPLETED, go to 6 and recheck.



9. Turn the ignition switch OFF.



10. Test the VTC oil control solenoid valve.



Is the VTC oil control solenoid valve OK?

YES - Go to 11.

NO - Replace the VTC oil control solenoid valve, then go to 14.



11. Check the camshaft timing.



Is the camshaft timing OK?

YES - Go to 12.

NO - Time the camshaft, then go to 14.



12. Check for damage to the cam chain.



Is the cam chain damaged?

YES - Replace the cam chain, then go to 14.

NO - Go to 13.



13. Inspect the VTC actuator.



Is the result OK?

YES - Go to 14.

NO - Replace the VTC actuator, then go to 14.



14. Turn the ignition switch ON (II).



15. Do the ECM/PCM RESET in the CLEAR MENU with the Honda PGM Tester or the HDS.



16. Do the CKP PATTERN CLEAR in the CLEAR MENU with the Honda PGM Tester or the HDS.



17. Do the ECM/PCM idle learn procedure.



18. Do the CKP pattern learn procedure.



19. Test-drive at a steady speed between 30-60 km/h (19-38 mph) for 10 minutes.



20. Check for Temporary DTCs or DTCs in the DTCs MENU with the Honda PGM Tester or the HDS.



Are any Temporary DTCs or DTCs indicated?

YES - If DTC P0341 is indicated, check for poor connections or loose terminals at the VTC oil control solenoid valve and the ECM/PCM, then go to 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC troubleshooting.

NO - Go to 21.



21. Monitor the OBD STATUS for DTC P0341 in the DTCs MENU with the Honda PGM Tester or the HDS.



Is it PASSED?

YES - Troubleshooting is complete.n

NO - If it is FAILED, check for poor connections or loose terminals at the VTC oil control solenoid valve and the ECM/PCM, then go to 1. If it is NOT COMPLETED, go to 19. and recheck.





Теперь про калибровку цепи



CKP PATTERN CLEAR/CKP Pattern Learn Procedure

Enable Criteria

ECT at 80°C (176°F) or higher.

Procedure



1. Do the CKP PATTERN CLEAR in the CLEAR MENU with the Honda PGM Tester or the HDS with the engine stopped.



2. Turn the ignition switch OFF.



3. Turn the ignition switch ON (II). Wait for 30 seconds.



4. Test-drive the vehicle on a level road and decelerate (with the throttle fully closed) from engine speed of 2, 500 rpm (min-1) to 1, 000 rpm (min-1) with in 2 or D3 position, or the M/T in 2nd or 3rd gear.



5. Stop the vehicle. Do not turn the ignition off.



6. Select the ALL DATA LIST in the DATA LIST MENU of the Honda PGM Tester or the HDS.



7. Check the status of PULSER F/B LEARN. If it is set to NG, the enable criteria was probably not met; repeat the procedure from the beginning.



калибровка проводиться только оригинальным сканером Honda





Вот показания с датчика осциллографа



Эти картинки с неправльными показаниями











Вот пправильные показания с датчика распредвала на хонде.







А так обычно спасает всех диагностика хонда у хорошего специалиста, кстати на хорошем сканере данные показания можно посмотреть в графике и без осциллографа
SOS
 
Сообщения: 10754
Зарегистрирован: Пт май 21, 2004 12:00 am

Re: Ошибка 057-03 P0341

Сообщение Реклама » Ср апр 04, 2012 10:12 am

Реклама
 
Сообщения: 10754
Зарегистрирован: Пт май 21, 2004 12:00 am

Вернуться в Электрика

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 1